Cisco / CCNA 200-301 v2.0

試験項目 3.4 · CCNA-104

HSRP / VRRP Operational Status

ドメイン 3 · IP Routing · First Hop Redundancy · HSRP / VRRP

このページのゴール

show standby / show vrrpの出力をInterface・Group単位で読み、Virtual IP、Local Role、Peer、Current Priority、Preemption、Trackingを組み合わせて現在の冗長状態とFailover後の状態を解釈できるようにする。

このページで学ぶこと

  • HSRP Show Standby Local Active
  • HSRP Show Standby Local Standby
  • HSRP Standby Unknown Redundancy
  • VRRP Show Local Master
  • VRRP Show Local Backup
  • FHRP Interface Group Scope
  • FHRP Target Group Identification
  • FHRP Current Versus Configured Priority
  • FHRP Tracking Priority Decrement
  • HSRP Operational Preemption Check
  • VRRP Operational Preemption Check
  • VRRP Owner Operational Recovery
  • FHRP Virtual IP Output Interpretation
  • FHRP Overall Operational Assessment

Operational Statusの読み順

Interface
↓
Group
↓
Virtual IP
↓
Protocol
↓
Local State
↓
Peer / Current Forwarder
↓
Current Priority
↓
Configured Priority
↓
Preemption / Tracking
↓
現在の冗長状態

Router全体を一括でActive / Masterとみなさず、Interface + Group単位で判断します。

HSRP出力の読み方

State is Active
Active router is local
Standby router is 10.0.0.3
Virtual IP address is 10.0.0.1

この例ではLocal Routerが現在のForwarderで、10.0.0.3が待機Routerです。

Standby router is unknownは待機Peerを認識できていない状態を示しますが、Local Activeが直ちに転送不能とは限りません。冗長性低下として評価します。

VRRP出力の読み方

State is Master
Virtual IP address is 10.0.0.1
Master Router is local

Local RouterがMasterなら現在のVirtual Gateway転送役です。Backup表示は正常な待機Roleになり得ます。

Group単位で読む

Gi0/0 Group 10 → Active
Gi0/0 Group 20 → Standby

同じRouter / InterfaceでもGroupごとにRoleが異なることがあります。対象Groupを取り違えないことが重要です。

Current PriorityとConfigured Priority

Trackingによって現在Priorityが変化している場合、設定値だけを見てRoleを判断しません。

Configured Priority = 105
Tracked Object Down → decrement 10
Current Priority = 95
Peer Priority = 100
→ 現在のElection / Preemption判断では95として評価

復旧時の判断

高Priority Routerが復帰した場合でも、HSRPではPreemption、VRRPでは通常のPreemption動作、VRRP IP Address OwnerではOwnerの特殊性まで含めて判断します。

重要な注意点

  • 高Priority ≠ 必ず現在Active / Master
  • Standby / Backup ≠ 障害状態
  • Standby router unknown ≠ Active Routerの転送が必ず停止
  • Configured Priority ≠ 必ずCurrent Priority
  • Active / Master ≠ Router全体の恒久的Role
  • Operational StatusはInterface + Group単位で判断

まとめ

show standby / show vrrpの出力をInterface・Group単位で読み、Virtual IP、Local Role、Peer、Current Priority、Preemption、Trackingを組み合わせて現在の冗長状態とFailover後の状態を解釈できるようにする。

理解確認

このページの内容を28問で確認します。

理解確認28問へ →